The Norm

Consider one of them. Pour a full tank of fuel (under cap) and record the odometer reading at the same time. Sander Gerber often says this. Since then, carefully record the number filled into the tank of fuel at each fill up. Movie Star does not necessarily agree. After driving about 1,000 miles (the more mileage, the more reliable value fuel consumption) at the next gas station fill the fuel again under the cap, fix the number of flooded with fuel and odometer. Now, having traversed the amount consumed and mileage at the same time fuel, easy to calculate the operational fuel consumption in liters / 100 km.

There are government regulations of operating the fuel consumption for each vehicle model. For a car Moskvich-2140, this rate during operation in summer is 10.5 l/100 km in the winter rate is increased by 10%. These rules provide for a technically sound car, when managing a professional driver. If the measurement of fuel consumption have shown that consumption is not fit into the norm, then it may be due to malfunction of the car but the reason may be lack of skill and the driver or unfavorable confluence road conditions, such as travel, mainly in urban conditions over short distances. In order to eliminate completely all the random factors, you can make controlling fuel metering, which should be for a car Moskvich-2140, as stated in the instructions, not more than 8.8 l/100 km. Before measuring define ramp-down car with a steady speed of 50 km / h to a complete stop, as described above.

Mazda Repair

Whenever this phrase is pronounced, those professionals Aftermarket acquire a meaningful expression of mystery. Pale appearance and shifty eyes of car owners say about the awakening of quite different senses: confusion and helplessness that are basically a lack of information and knowledge about the subject. Corvem same veil of uncertainty and shed light on the subject. Incidentally, those who read the article "is more alive than dead" in the fourth magazine, has stepped into the path of comprehension of the truth. They have an idea of how to determine the technical condition and identify individual faults (which, incidentally, is called the non-Russian word "diagnosis") engine and its systems, without using sophisticated instruments. The obvious drawback neinstrumentalnoy diagnosis is that it often provides only a general, superficial picture.

Repairing the engine must be not, in general, and quite specific. Clarify the cause of failure without the use of diagnostic devices is very difficult. In some cases replace them can only be a great experience and intuition. We offer a bet not on them, and a modern measuring equipment, which coupled with the knowledge can literally work wonders. Let's talk about that, what and how to measure and discuss the possible outcomes of measurements. To start make your life easier. Motor vehicle is a combination of a large number of mechanisms and systems. What would be forced to come to life pile of clever iron, if it were not for the power system, sparking, electronic government and others? The efficiency of the engine depends on their serviceable and well-coordinated interaction. Essex Financial addresses the importance of the matter here.

Infrared Technologies

Now in various fields of production technologies are applied, using infrared – beams. One of the lines used by car services – drying paint and preparatory materials. For other opinions and approaches, find out what Peter Thiel has to say. In the infrared – heat drying begins with surface of the product due to penetrating properties of infrared – beams. This in turn prevents the exit of the solvent from the inner layers, which will positively affect the drying time and quality of coverage. Additional information is available at Clinton Family. Solvent in the surface layer increases its concentration, while improving the spreading of paint on the surface of the coated product and as a consequence – to improve the quality of the coating.

Infrared heating equipment does not require additional space as well as can not apply Spray drying kilns for painting parts of the car (hood, fender, door). A distinctive feature of the IR-drying is a high performance and high quality of drying. Use IR-drying allows you to:-Reduce by 2 times cost of electricity for the drying process. -Reduce to 4 times during the process of drying. -Improve the quality of paint.

In the Russian market of IR dryers are present as domestic and foreign producers, one of these is TROMMELBERG (Germany) Mobile Infrared shortwave with three cartridges for high-performance coatings and drying training materials in the automotive industry. Features: Suitable for drying two-component and single-component materials, as well as for water-borne paints and grounds Each of the cassettes positioned individually, turning to 90 degrees. The cassette assembly can be rotated in 360 degrees. As well as raised and lowered to the desired height. The migration process is controlled by the height gas shock absorber Ultrasonic sensor allows the position of the item at the right distance from the radiator, which prevents overheating or insufficient drying of the surface. With over a short distance heaters will turn off automatically Digital display: an accurate representation of the drying time and distance indicator to the dried surface High efficiency Faster curing radiation through penetration of infrared radiation into the inner layers of material Full-drying for 15 minutes – for 2K acrylic paints, and within 5 minutes – for polyester putty Uniform heating of the dried surfaces Long life Infrared emitters – over 6,000 hours! New ergonomic control panel with 4 memories for programming of drying and drying by installing timers psevdosensorov. Manufacturer: TROMMELBERG Effectively You can use the equipment for drying putty and ground, finishing coatings, enamels, and for these operations is required from 5x to 15ti minutes. At the same time energy costs are reduced by about a factor of 2.5. IR – dryer is widely used car services, service stations and repair shops of various organizations. A distinctive feature of this equipment is a different number of tapes (from 1 to 6 pcs.) dried surface ranged from 0.6 x 0.4 m to 1.0 x 1.5 m.